There are many sources of problems, you might start worry. These include: inadequate, incompatible, or incorrectly configured hardware is incompatible (software) device driver or a recently installed programs.
Problem: The screen remains blank when you switch on your PC.
Cause: - that you are not in a position to even the BIOS POST screen indicates problem with the underlying hardware.
Solution: Work on the power supply, video card and motherboard troubleshooting sessionsbefore other components.
Problem: Your XP computer stops responding when you start
Cause - 1: - A device driver or a recently installed software or is terminated from windows to boot normally. There is a corruption in the Windows registry has been.
Solution1A: - Restart the computer and register XP in Safe Mode. Open Device Manager and look for problematic devices. Make sure that the jumpers are set properly on the hardware. If the hardware correctlyconfigured and you still have the problem, then it could mean that the device driver for the hardware must be updated. Remove the device from the Device Manager and reboot as usual. Get the updated device drivers for the hard goods (via the Internet, CD, etc.), run the hardware wizard and install the device driver.
Solution1B: - Restart the computer in Safe Mode. If the problem is not the hardware drivers, or you do not see any problematic devices in the deviceManager, start the System Restore to roll back the computer was at an earlier time, when you know it to function normally.
Solution1C: - If System Restore does not get to start your computer normally, the Windows Advanced Options menu will "and select" Last Known Good Configuration ". Windows XP starts your computer using the registry information from the last shutdown.
Solution1D: - If the "Last Known Good Configuration" does not work, then the final course of action is to not include inPlace Upgrade. Start the Windows XP setup program from the installation CD.
Solution1E: If you suspect that the recently installed system service caused the problem, stop the service by running the steps earlier.
Cause: II: - the BIOS is not correct.
Solution: - II: - Restart the computer and enter the BIOS set to the screen. If you have changed any settings, they again prior to the values. If you are sure about the previous values, or have not changedthe settings, select Load Fail-Safe Defaults option and reboot.
Cause: III: - It could be a hard disk failure or data corruption in the boot records.
Solution: - III: - Insert the Windows XP installation CD, and once you start the computer. Welcome to the Setup screen, press R to start the Recovery Console. You will enter the management password. Enter the password, or if the password is blank, press (Enter). At the command prompt, type "chkdsk". This willRun the Disk Utility to verify that the hard drive for all the scanning error. Check disk report may be a hardware error or errors on your hard drive. If this is the case, it is best for your PC to make the repair professional.
Problem: You receive an error message when Windows XP starts.
Cause: - A recently installed file or service or software program is compatible with Windows XP and preventing it from starting. Exactly the error message look. If a file or service names are mentioned in theError then you shoot problems, either through a clean start or stop the service can.
Solution1A: - To make a clean boot in Windows XP, use the following step.
1. Start the System Configuration Tool by clicking Start> Run, typing "msconfig" and press Enter.
2. Click Selective Startup, and uncheck the following check boxes. "Process System.ini File, Process Win.ini" and "load startup items"
3. Select the Services tab and click "Hide all MicrosoftServices "check box and then select" Disable All ".
4. Click "OK" and then "new" to restart the system
5. When Windows is restarted if the error does not occur, go to "msconfig" and click on "File" System.ini "process" check box and click OK and restart your computer. If the problem you know that the problem is with one of the system.ini entries. If the error no longer occurs, can gradually the remaining check boxes. Restart the computer after you make each controlField until the error occurs again.
6.Once you have the area in which the error occurs, turn off the record or stop / disable the service as the case may be identified.
Making Solution1B: - If you are not capable of making a clean start you have trouble shooting the problem and you know the name of the service, then you start the Recovery Console, as explained above. From the command prompt to change to the system 32 folder. Enter "listsvc" at the command prompt in the System 32 folder. A list of all services onYour computer will be displayed. Find the name of the service that is causing the error. Enter "Clear" and press Enter. The computer is a message to the list of "Startup Type" to be shut down to that. They note in case you need to re-activate the service. Type "exit" and let the computer restart normally.
Solution1C: - If you recently introduced a program to install causes this error, remove the program. If the program does not have to remove in the list / list, visitDeveloper website for instructions on removing the program.
Problem: After upgrading programs that load at startup was not started.
Cause: This symptom is noticed when you are first time after upgrading from Windows 98 or ME. Windows XP, all programs from the startup list, remove it feels are not compatible.
Solution: Click Start> Run, type "msconfig" and press Enter. Click the Startup tab. Select the "Restore from Startup Programs" Optionand click OK. Restart the computer.
Atom Feed (xml)
ไม่มีความคิดเห็น:
แสดงความคิดเห็น