Brother Printer Cartridges
The refilling this cartridge is messy, it is therefore important to note that gloves should be worn, and the place where refilling is done should be covered with a newspaper or other absorbent material.
The following steps, you can create a simple guide to refill your Brother printer cartridges. The different models have little variations remain in the other procedures are the same.
Brother printer cartridge LC01C, LC01Y, LC01M and LC01BK (MFC 7000Series)
1. Set amongst all absorbent material like a towel before refilling the brother ink cartridges.
2. After filling ink in the syringe bottle remove the needle and put the cone-shaped adapter on it.
3. Find the hole in the cartridge through the ink flow and turn the port count in front of your lap.
4. Slowly inject the ink from the syringe into the bottle until the cartridge ink starts coming out of the vent hole and is not foamy.
5. Now turnthe cartridge in the other way around so that the vent hole faces you and the exit port of your lap.
6. Insert the needle into the syringe bottle and inject the needle into the vent hole. Continue injection until the ink comes out of the exit hole and keeps foaming.
7. Leave the cartridge in this position for about ten minutes. Then repeat the 6th Step and let rest for ten minutes.
8. Install the cartridge into the printer. If it must then be a transportElectrical tape can be used to cover the departure and air holes, but must be removed before printing.
Brother printer cartridges for Brother MFC-7150 and MFC-7160
It is a sponge in the cartridge, the refilling process makes sticky. The first step remains the same.
1. Locate the exit hole in the ground, where there is a large plug.
2. So look for the vent on the bottom that exists on the same side as the big handle on the top of theCartridge.
3. Turn the exit port in the direction of the Round Square of the vent hole on the right side and vice versa. Seal the exit port with a black electrical tape.
4. Take the deal on the top of the cartridge. Inside, you'll see two metal seals, the smaller round and the larger rectangular. Remove the seal or puncture holes in them.
5. To fill the syringe with ink bottle, you squeeze the bottle and syringe, the needle is inserted into the ink bottle. Relax and let the handlethe syringe suck the ink in the bottle.
6. Under the syringe bottle slowly inject the ink into the sponge through the deep rectangular opening, to saturate the sponge.
7. Also ink injected into the round hole that is filled to the outer chamber. After injection, carefully seal the round hole with black electrical tape. Also seal the rectangular hole with tape.
8. Reset the plastic handle at the top. Take the cartridge to a sink and remove the tape from the bottom. Let the additionalDrops of ink to flow away.
9. Printer should now be installed.
Brother printer cartridge LC41C, LC41Y, LC41M and LC41BK
In this model, because the ink receiving the valve. The first step is the same.
1. Find the label marked with the letters as LC41 C, M, Y or BK represented colors.
2. Hold the label side up, on the right side you will find a window on the top of the cartridge. Make a hole in the window with a smoldering iron or some heated metal thing.
3.Fill the syringe bottle Step 5 as mentioned above.
4. Inject the ink slowly with the syringe into the bottle, the top right window on the cartridge. Fill the entire cartridge.
5. Close the window with black electrical tape.
6. Insertion into the printer.
Brother printer cartridge HJ100 and HJ400
It is very different in this cartridge. The first step remains the same.
1. Start with a screw in the vent, which is the longest side of the cartridge oppositeThe contrary, the print head.
2. Draw out the plug with screw. Fill the syringe bottle with ink and then add half to the hole. Inject slowly and deeply into the sponge.
3. Expect a few drops. Tape the cartridge, you have to transport it.
Toner
Refilling of toner is very similar to a paste adding petrol or gas to your car. Refilling of toner should be done in a place where there is no wind. It can burn, just work, where itno flame. Do not breathe too, as it is irritating.
The three basic types of laser toner cartridges are:
o canister: a tube for holding toner
o Drum: a cartridge with gears and a drum, a gelatin-coated
o toner and developer: similar but drum cartridge with toner and developer both.
Canister Cartridge
1. Spread some absorbent material like a towel or newspaper. Looking for a plug at the end of the cartridge.
2. Pull the plug, if you find it. IfYou do not then create a hole, which is itself) from the paper (smooth plastic surface.
3. If you have a hole then gently the chips. 4. Shake the bottle of toner and pour the whole bottle into the cartridge with a funnel or paper funnel.
5. Put the plug back and seal it with a black electrical tape.
6. Insertion into the printer. The refilling of these cartridges can be done, a lot of time.
Drum Units
These are more complex cartridges. The'pretty' drum can have three colored coatings: red, blue or green. When topping have to find the toner hopper and the waste containers.
o Locate the drum and imagine that it runs until the end of the cartridge.
o Lay It Down, that the drum runs from left to right in front of you. The site near to you is the "this side" and a far away from you "beyond".
o One of these sites is larger than the others.
o The main page is "toner container and is a small"Waste Funnel".
Now, for refilling the following steps to follow.
1. Locate the drum but do not touch it. It may be in a shutter speed.
2. Find the toner hopper. You will see a translucent plug on one side. Remove it. If you do not find a hole in the funnel to create toner from the paper path.
3. Vacuum the drum of shavings but do not touch the drum.
4. Shake the bottle of toner and pour the whole bottle into the cartridge with a funnel.
5.Seal the hole withthe pug or a black electrical tape.
Toner Cartridges & Developer
This cartridge is very similar to the drum cartridge but it has two plugs. The greater will be smaller for the toner and developer. You need medium-sized flat and cross headed screwdrivers.
1. Here you will find the waste in the box at the end of the cartridge, remove and then tighten the screws. There is a sliding door for the garbage.
2. Behind the litter box a plastic plate with a single screw is required. You are an arrangement to make it in such aManner that is the green colored part on the upper right and lower left screw. Screw you open it.
3. There is a clip on the green side. Push it with a flat screwdriver to release the plate.
4. You will see a large cap for the toner. Get off at the cap or make a hole in it.
5. Fill the cartridge with toner and seal them.
6. On the way to the left of the center is a small plug for the developer. Make a hole or pull it.
7. Fill the hole with developers and seal.
8.Place the plastic plate and the waste container.
9. Shake the cartridge gently.
Atom Feed (xml)
ไม่มีความคิดเห็น:
แสดงความคิดเห็น